Install Guide; Spec Sheets. Glean a morsel of inspiration from our extensive glass tile photo. Oceanside Glasstile manufacturing combines precision engineering. How to Install Glass Wall Tile. Do not install glass tile over. the flat of the trowel to a thickness of 1/8 inch. Use white thinset with glass tile. How to Install Glass Tile (with Pictures)1. Choose a grout. There are two main types of grout: sanded and unsanded grout. Sanded grout is used when the gaps between tiles are larger than 3mm. ![]() ![]() Bosch 1/8 in. glass and tile. Rated 3.0 out of 5.0 by bart they work till they break I had 2 toilet flanges to install on top of the tile. 12. The shaft is 1/8.
Unsanded grout is used when the gaps between tiles are smaller than that. Measure the gaps between your tiles to find out which grout is best for your project. Glass tiles almost always come in sheets these days and these sheets tend to have very small gaps between the tiles, meaning you will probably want unsanded grout. It is important to choose the right grout for your project because not doing so will cause cracks (and all the problems that come with them) in your tiles. There is also technically epoxy grout, which you can use, but it is more expensive and difficult to apply if you do not have experience applying grout. Mix your grout. Mix your grout according to the instructions on the packaging, making sure to also mix in any additives you want. It should have a consistency like smooth peanut butter. Make sure that you mix no more than what you can spread in 2. This will keep the grout from drying out. You should only work on small areas at a time, finishing one section before continuing on to the next, so plan on mixing many small batches of grout. You can get grout additives that make it more mold resistant or water resistant, as well as additives that do things like giving the grout a color. Spread your grout. Grab a grout float and get ready to spread! Working in only a small area at a time (again, what you can cover in 2. ![]() ![]() Hold the float at a 4. You do not want to move the float parallel or perpendicular to any tiles, since this will push the grout out of the gaps. Let the grout cure for 2. Use the float to remove the major excess grout and then let the grout begin to cure. Wait roughly 2. 0 minutes, or whatever time is recommended in the instructions for your specific product, so that the majority of the grout can set enough for you to remove the excess that is on the tiles. Remove the excess. Get a large bucket of sink- full of water and a large sponge. Get the sponge wet and then wring out the excess water, so that it is only damp. You want to have as little water on the sponge as possible. Now, wipe all along the tiled area to clean off the excess grout. Do not press very hard or you will remove the grout between the tile. Rinse and wring your sponge frequently, keeping it as clean as you can. Get new, cleaner water as needed. Let the grout cure. Once you have grouted all of the tiled area, allow the grout to cure. You should follow the instructions for your specific product but generally three hours are needed to cure grout properly (as many as 2. Make sure that the area is well ventilated and that moisture is kept to an absolute minimum. Seal the grout. Once your grout has cured, you will want to seal your grout. This step is often skipped but you should not skip it if at all possible. Sealing your grout will be very important in keeping it from getting moldy or stained. Find an appropriate grout sealant at your local hardware store and apply it according to the included instructions. Usually, the sealant will be wax- like and is applied using a rag. Rub it in circular motions along the grout lines to apply. Grout will need to be resealed roughly every 6 months and should at least be resealed once a year. Caulk as needed. If you need to, you can apply caulk as needed around your new tiles. This may be useful at the corners and along the seams, such as if you have applied a short backsplash along a wall. Simply caulk the line, shape the caulk by running your finger down the line, and let it set.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
September 2016
Categories |